Hey, i was wondering the rating on my winch, info that i have searched is limited and conflicting. Its a pto driven braden lu-2 that is on my 66 w200 powerwagon.Its also my first pto driven winch on anything less than a 5 ton truck. Is this winch heavy enough for this truck? It will be getting a d60/14bolt swap, 38 inch tsl's for now with the plan to go to 42's in the near future. The drivetrain will remain stock so no added weight from doublers but it will be getting a cage in cab and an additional fuel tank and some axle trussing. Thats about it for additional weight. Thanks
Figure out what cable you have on it (Have to count the number of groups, and wires in each group), you can safely use that as your rating (assuming the hook is installed properly), up to 12000 lbs. As you know form the duces, the designed weak link is the shear pin. Take it out, and get a machinist to make you several spares. I've had both my Ramseys (same basic design) apart, and everything inside is so much more beefier then my 12 K electric.
And whatever you do, don't just replace the shear pin with a bolt and if a previous owner did that, put a shear pin back in. If you do ever overload the winch, it will bust the housing and make it a nice, heavy boat anchor.
I have a swivel hook on my wire rope but generally use a length of chain like the military winches do but I can take it off if needed. It's just a lot more versatile that way.
Ok, thanks for the pic, just one more question, about the size and rating on your swivel hook. In my mind it looks a bit small, thats alot of force to be pulling on the little swivel pin. Also what size wire rope are you using?
It's actually pretty large for just a winch hook. It's a 5/8" hook and it's WLL is 5 tons. The wire rope is 3/8" with a WLL of about 2.4 tons but the minimum break is just over 12k lbs. Keep in mind that all the 8k lb commercial winches available today run 5/16" wire rope that has a WLL of only 1,700 lbs. For a better size reference of the winch and hook, here's a pic of the whole truck:
As you can see, it's a BIG winch for only an 8k lb rating, but it's 50 years old also. If you need wire rope, I recommend AWdirect.com.
For hooks, and chains, and such do not just go by physical size, they come in different grades just like bolts do. There is many places on the web that list the specs.
I didnt realize the swivel was 5/8". Also thanks for the ref. My winch has 7/16 cable on it right now but its probably as old as the truck. Ill probably be replacing it with the same dia.
For grade, I dont go with anything less than transport grade for any hooks or chain i have (g70)
I'm thinking of mounting a set of bearings in the drivers side engine mount, then making a short shaft to mount in it. from there, it would have a short shaft going to the winch, and another going back to the PTO. Lot of it will depend on how things line up once I get the winch mounted.
Thats kinda how I thought it went. I would have to make a plate to block off the CAD.
My PTO mounts on the drivers side of the tranny, not the trannsfercase, so the angles would be too tight.
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Related Threads
?
?
?
?
?
Dodge RamCharger Central
1.3M posts
72.2K members
Since 2002
RamchargerCentral.Com is a Dodge truck community built by a vast number of experienced owners. Whatever you're thinking about doing from routine maintenance to full-on restoration, odds are somebody around here already has. Originally focused on the Ram Charger / Trail Duster, our members own, drive and wrench on Mopars from the 40s to the current day. It's not what you buy, it's what you build.